Copyright ©2010 Microscan Systems, Inc. 9
MS-820-to-QX-830 Compact Industrial Scanner Transition Guide
MS-820 Alpha Commands Supported in the QX-830
The following table shows MS-820 alpha commands that will function in the QX-830. The QX-830 is
intended for use with numeric commands, but the commands shown below can be used in the QX-830.
Important: Microscan does not guarantee support for these commands in future versions of the QX-830.
Alpha Commands Numeric
Communications
Host Port Connections <Kabaud rate,parity,stop bits,data bits><K100>
Auxiliary Port
<Kyaux port mode,baud rate,parity,stop bits,data bits,daisy chain status,daisy
chain ID>
<K101>
Preamble <Kdstatus,preamble><K141>
Postamble <Kestatus,postamble><K142>
Response Timeout <KAresponse timeout> <K143>
LRC Status <Kcstatus> <K145>
Read Cycle
Trigger Mode <Kgtrigger mode,filter time><K200>
Serial Trigger
Character
<Kiserial trigger character> <K201>
External Trigger State <Kjexternal trigger state> <K202>
End of Read Cycle <Khmode,read cycle timeout> <K220>
Good Decode Reads <Kmgood decode reads><K221>
Multisymbol
<
KL
number of symbols,multisymbol
separator> <K222>
Motor On/Scan Speed <KE> <K500>
Motor Off <KF> <K501>
Maximum Element <KImaximum element>> <K502>
Laser Controls <KClaser on/off,laser framing status,laser on position,laser off position><K700>
Symbologies
Narrow Margins /
Symbology Identifier
<Konarrow margins,symbology identifier status><K450>
Background Color <Kxbackground color><K451>
AIAG
<KZstatus,ID1,status1,ID2,status2,ID3,status3,ID4,status4,ID5a,ID5b,ID5c,
status5,ID6,status6,ID7,status7,ID8,status8,ID9,status9,ID10,status10,ID11,status
11,ID12,status12>
<K454>
Code 39
<Kpstatus,check digit status,check
digit output status,large intercharacter
gap,fixed
symbol length status,fixed symbol length,full ASCII set>
<
K470
>
Codabar
<Kqstatus,start and stop match status,start and stop output status,large
intercharacter gap,fixed symbol length status,symbol length,check digit type,
check digit output>
<K471>
Interleaved 2 of 5
<
Kr
status,check digit status,check digit output,symbol length 1,symbol length 2>
<
K472
>
UPC/EAN
<
Ks
UPCstatus,EAN status,supplementals status,separator status,separator character>
<K473>
Code 128 / EAN 128
<Ktstatus,fixed symbol length status,
fixed symbol length,EAN-128 status
,
output
format,application record separator status,application record separator
character,
application record brackets,application record padding>
<K474
>
Code 93 <K!status,fixed symbol length status,symbol length> <K475>
PDF417 <K[status,raster sweeps before decode attempt,fixed length status,symbol length><K476>
I/O Parameters
Serial Verification
<
KS
command echo status,command
beep status,control/hex output>
<
K701
>
Beeper <Kustatus,volume><K702>
Quality Output <KJquality output separator,decodes/trigger status,decode direction output>> <K704>
Symbol Data Output <Klsymbol data output status,when to output><K705>
No Read Message <Kkstatus,message><K714>
Bad Symbol Message
<K’status,message><K715>
No Symbol Message
<KNstatus,message><K716>
For Assistance, contact the Automation Group at Cross 800.866.4568
(102 Seiten)
(2 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern