Microscan MS-2 Bedienungsanleitung Seite 47
- Seite / 125
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
MS-2 CCD Reader User’s Manual 4-1
4 Read Cycle
Contents
After you’ve established communications you will need to address the spatial and timing
parameters associated with your application. This section explains those parameters.
Read Cycle by ESP ...................................................................................................................... 4-2
Read Cycle Serial Commands......................................................................................................4-3
MS-2 Read Cycle Overview.......................................................................................................... 4-4
Number of Symbols ......................................................................................................................4-5
Time Between Identical Decodes .................................................................................................4-6
Trigger Mode ................................................................................................................................4-7
Continuous Read 1 Output Emulation ..........................................................................................4-9
Serial Trigger Character (Delimited)...........................................................................................4-10
Start Trigger Character (Non-Delimited)..................................................................................... 4-11
Stop Trigger Character (Non-Delimited).....................................................................................4-12
No Decode Timeout.................................................................................................................... 4-13
Decodes Before Output .............................................................................................................. 4-14
No Read Message...................................................................................................................... 4-15
Reader Setup.............................................................................................................................. 4-16
- MS-2 CCD Reader 1
- User’s Manual 1
- Disclaimer 2
- Latest Manual Version 2
- Technical Support 2
- What Is Covered? 3
- What Is Excluded? 3
- Limitation of Liability 3
- Table of Contents 4
- About the MS-2 CCD Reader 6
- About This Manual 6
- Highlighting 6
- Host Communications 6
- Warning and Caution Summary 7
- Statement of RoHS Compliance 9
- MS-2 CCD Reader User’s Manual 10
- 1 Quick Start 11
- Step 1 — Check Hardware 12
- Step 2 — Connect the System 13
- Step 3 — Install ESP 14
- Step 4 — Select Model 15
- Step 5 — Autoconnect 16
- Step 6 — Position the Reader 17
- Step 7 — Configure the Reader 18
- Saving Options 19
- Save Configuration in ESP 20
- 2 Using ESP 21
- Application Mode 23
- Menu Toolbar 24
- Preferences > General Tab 26
- Preferences > Terminal Tab 27
- Sizing Information 28
- Preferences > Advanced Tab 29
- (cont.) 30
- Connect to Readers via TCP/IP 30
- Use Default Storage Location 30
- Document Memo 31
- Model Memo 31
- Autoconnect 32
- Autoconnect (cont.) 33
- Navigating in ESP 35
- Send/Receive Options 36
- Defaulting 37
- Advanced Options 37
- 3 Communications 39
- Communications by ESP 40
- Host Port Connections 42
- Host Port Protocol 43
- Preamble 44
- Postamble 45
- 4 Read Cycle 47
- Read Cycle by ESP 48
- Read Cycle Serial Commands 49
- MS-2 Read Cycle Overview 50
- Number of Symbols 51
- Trigger Mode 53
- External Edge 54
- Serial Data 54
- Serial Data and Edge 54
- No Decode Timeout 59
- Decodes Before Output 60
- No Read Message 61
- Reader Setup 62
- 5 Symbologies 63
- Symbologies by ESP 64
- Symbologies Serial Commands 65
- Full ASCII Set (Code 39) 67
- Symbol Length (Codabar) 69
- Interleaved 2 of 5 70
- Minimum Length 71
- Fixed Length 71
- Code 128/EAN 128 72
- GS1 DataBar (RSS) 74
- MSI Code 75
- Plessey Code 76
- Industrial 2 of 5 77
- UPC-A Status (UPC/EAN) 79
- UPC-E Status (UPC/EAN) 79
- EAN-8 Status (UPC/EAN) 79
- EAN-13 Status (UPC/EAN) 80
- UPC-A as EAN-13 (UPC/EAN) 81
- UPC-E as UPC-A (UPC/EAN) 81
- EAN-8 as EAN-13 (UPC/EAN) 81
- Symbology Identifier 82
- Terminal 83
- Terminal Window 84
- Editing a Macro 87
- Terminal Window Menus 88
- Utilities 89
- Serial Utility Commands 90
- Differences from Default 91
- Firmware 92
- Firmware Verification 94
- Device Control 95
- Default/Reset/Save 96
- Reader Status Request 97
- General Specifications 100
- MS-2 CCD Reader Dimensions 100
- Appendices 101
- Serial Configuration Commands 104
- Serial Command Format 105
- Appendix E — ASCII Table 108
- Appendix F — Operational Tips 109
- 5 Volt Devices 110
- 10-28 Volt Devices 110
- Hyperlink Index 115
- Variable Length 124
- Very Large-Scale Integration 124
- Warranty 124
- Recipient Response 125
Verwandte Produkte und Handbücher für Barcodeleser Microscan MS-2
Barcodeleser Microscan HE45T Bedienungsanleitung
(102 Seiten)
(102 Seiten)
Barcodeleser Microscan MS-4Xi Bedienungsanleitung
(360 Seiten)
(360 Seiten)
(2 Seiten)
Barcodeleser Microscan QX Hawk Bedienungsanleitung
(460 Seiten)
(460 Seiten)
Barcodeleser Microscan MS-4X Bedienungsanleitung
(312 Seiten)
(312 Seiten)
Barcodeleser Microscan HS-51X Bedienungsanleitung
(156 Seiten)
(156 Seiten)
Barcodeleser Microscan MS-4X Bedienungsanleitung
(374 Seiten)
(374 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern